RE: New Verizon PVC

As far as you needing PVCs and PPPoE set on the subinterfaces, you
already took care of that with your vc-class profile.

Seth Crimmins
Westelcom Internet

-----Original Message-----
From: owner-verizonisp@westnet.com [mailto:owner-verizonisp@westnet.com]
On Behalf Of Matthew Crocker
Sent: Tuesday, August 21, 2007 4:19 PM
To: verizonisp@westnet.com
Subject: Re: New Verizon PVC

> Hello, we are new with verizon east for DSL Resale, we finally got
> our OC3 installed, which is up w/o any errors. We have not been
> able to get any info from verzion how to setup the pvc.
> We are using cisco 7206 and found some info on cisco site and our
> config for atm/pvc is below.
> basically the cpe isnt able to login or get a ip address when we
> connect to test dsl lines we ordered.
> have attached the sh interface as well.
> not sure if part of it not working is when verizon had asked us for
> mac address of router we had provided mac of ethernet interface
> (does that mac address have to be assigned to OC3 interface as well?)
>
> If some can please help out on this, we havent been able to get any
> where with vz or if someone can please provide consulting

There is a MAC address associated with the OC-3 and Verizon needs to
have the correct one. That is probably why your testing doesn't
work. Verizon sees your OC-3 MAC address and is throwing the packets
away because it doesn't match the one you are gave them. I forget
how to access the MAC address on an ATM OC-3 card. You probably
also need to create a bunch of PVC sub interfaces on your ATM
circuit. Once for each PVC Verizon is sending you (one per Redback on
here). Then you run PPPoE on each sub-interface to handle the
customer connections. Verizon should give you a list of sub-
interfaces/PVCs you'll need to create.

I have a Redback SMS 1800 handling my PPPoE sessions so I don't know
how you would set it up with Cisco.

> sincerely
> jim
>
> bba-group pppoe global
> virtual-template 1
>
> vc-class atm auto-pppoe
> protocol pppoe
> ubr 155000
> create on-demand
> pppoe max-sessions 200
> !
> interface Loopback0
> no ip address
>
> !
> interface ATM1/0
> no ip address
> class-int auto-pppoe
> no atm ilmi-keepalive
> !
> interface Virtual-Template1
> ip unnumbered Loopback0
> peer default ip address pool pppoepool
> ppp max-bad-auth 3
> ppp mtu adaptive
>
>
> ip local pool ppoepool 192.168.40.20 192.168.40.50
>
>
>
>
>
> show results for interfaces
>
>
> ATM1/0 is up, line protocol is up
> Hardware is ENHANCED ATM PA
> MTU 4470 bytes, sub MTU 4470, BW 149760 Kbit, DLY 80 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation ATM, loopback not set
> Encapsulation(s): AAL5
> 4095 maximum active VCs, 0 current VCCs
> VC Auto Creation Enabled.
> VC idle disconnect time: 300 seconds
> 1 carrier transitions
> Last input never, output never, output hang never
> Last clearing of "show interface" counters never
> Input queue: 0/75/0/0 (size/max/drops/flushes); Total output
> drops: 0
> Queueing strategy: Per VC Queueing
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 0 packets input, 0 bytes, 0 no buffer
> Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
> 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
> 0 packets output, 0 bytes, 0 underruns
> 0 output errors, 0 collisions, 0 interface resets
> 0 output buffer failures, 0 output buffers swapped out
> Virtual-Access1 is down, line protocol is down
> Hardware is Virtual Access interface
> MTU 1500 bytes, BW 100000 Kbit, DLY 100000 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation PPP, LCP Closed
> Base VtMgr vaccess
> Vaccess status 0x0, loopback not set
> DTR is pulsed for 5 seconds on reset
> Last input never, output never, output hang never
> Last clearing of "show interface" counters 3w3d
> Input queue: 0/4096/0/0 (size/max/drops/flushes); Total output
> drops: 0
> Queueing strategy: fifo
> Output queue: 0/40 (size/max)
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 0 packets input, 0 bytes, 0 no buffer
> Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
> 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
> 0 packets output, 0 bytes, 0 underruns
> 0 output errors, 0 collisions, 0 interface resets
> 0 output buffer failures, 0 output buffers swapped out
> 0 carrier transitions
> Virtual-Template1 is down, line protocol is down
> Hardware is Virtual Template interface
> Interface is unnumbered. Using address of Loopback0 (0.0.0.0)
> MTU 1500 bytes, BW 100000 Kbit, DLY 100000 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation PPP, LCP Closed, loopback not set
> Keepalive set (10 sec)
> DTR is pulsed for 5 seconds on reset
> Last input never, output never, output hang never
> Last clearing of "show interface" counters 3w3d
> Input queue: 0/75/0/0 (size/max/drops/flushes); Total output
> drops: 0
> Queueing strategy: fifo
> Output queue: 0/40 (size/max)
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 0 packets input, 0 bytes, 0 no buffer
> Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
> 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
> 0 packets output, 0 bytes, 0 underruns
> 0 output errors, 0 collisions, 0 interface resets
> 0 output buffer failures, 0 output buffers swapped out
> 0 carrier transitions
> Virtual-Access2 is up, line protocol is up
> Hardware is Virtual Access interface
> MTU 1492 bytes, BW 100000 Kbit, DLY 100000 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation PPP, LCP Closed
> Base PPPoE vaccess
> Vaccess status 0x44, loopback not set
> DTR is pulsed for 5 seconds on reset
> Last input never, output never, output hang never
> Last clearing of "show interface" counters 4d03h
> Input queue: 0/4096/0/0 (size/max/drops/flushes); Total output
> drops: 0
> Queueing strategy: fifo
> Output queue: 0/40 (size/max)
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 0 packets input, 0 bytes, 0 no buffer
> Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
> 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
> 0 packets output, 0 bytes, 0 underruns
> 0 output errors, 0 collisions, 0 interface resets
> 0 output buffer failures, 0 output buffers swapped out
> 0 carrier transitions
> Loopback0 is up, line protocol is up
> Hardware is Loopback
> MTU 1514 bytes, BW 8000000 Kbit, DLY 5000 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation LOOPBACK, loopback not set
> Last input never, output never, output hang never
> Last clearing of "show interface" counters never
> Input queue: 0/75/0/0 (size/max/drops/flushes); Total output
> drops: 0
> Queueing strategy: fifo
> Output queue: 0/0 (size/max)
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 0 packets input, 0 bytes, 0 no buffer
> Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
> 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
> 0 packets output, 0 bytes, 0 underruns
> 0 output errors, 0 collisions, 0 interface resets
> 0 output buffer failures, 0 output buffers swapped out
>
>
> ______________________________________________________________________

> __
> Send your friends personalized video messages!
> Sign up for a FREE Juno account and start sending Video Mail today!
> http://track.juno.com/s/lc?u=http://ads.addynamix.com/click/
> 2-2130421-177
>
>
>
> Recent archives of the list can be found at
> http://www.westnet.com/verizonisp/
> Send 'unsubscribe' in the body to verizonisp-request@westnet.com to
> leave.

Recent archives of the list can be found at
http://www.westnet.com/verizonisp/
Send 'unsubscribe' in the body to verizonisp-request@westnet.com to
leave.

Recent archives of the list can be found at
http://www.westnet.com/verizonisp/
Send 'unsubscribe' in the body to verizonisp-request@westnet.com to leave.
Received on Thu Aug 23 18:08:35 2007